Tap Drill Size Chart

M24 x 2 Tap Drill Size

Tap drill

22 mm 0.8661 in

Use a 22 mm drill (0.8661 in) for 77.0% thread.

Fine thread M24 x 1.5? Use 22.5 mm. (0.8858 in, 77.0% thread)

The drill size for a M24 x 2 tap is 22 mm (0.8661 in). If you are wondering what size drill bit a M24 x 2 tap needs, that is the one: it leaves 77.0% of thread, which is the figure standard tap and drill charts are built around. Below are the other holes you might want for this size - a larger drill for tough material, the form-tap hole, and the clearance holes for the bolt that goes in.

Every drill for M24 x 2

Tap drills and clearance drills for M24 x 2 (Metric fine, 2 mm pitch). Percent of thread is the figure stored for each drill, which reproduces from the major diameter and pitch of M24 x 2.
Use Drill Decimal in mm % thread
Standard tap drill Cut tap, general use (D - P) 22 mm 0.8661 22.00 77.0%
Inch substitute Closest inch drill if you have no metric set 55/64″ 0.8594 21.83 83.6%
Hard material Stainless, tool steel, anything that fights the tap 22.5 mm 0.8858 22.50 57.7%
Form (roll) tap Theoretical 23.12 mm - starting point, check your tap maker's chart 23 mm 0.9055 23.00 —

Clearance holes for a M24 x 2 bolt

A clearance hole is not tapped. It is the hole in the part the bolt passes through, so it is always larger than the thread.

Clearance holes for M24 x 2 per ISO 273. Clearance depends on the bolt diameter alone, so every M24 thread shares these figures.
Fit Hole mm Hole in
Fine 25.00 0.9843
Medium 26.00 1.0236
Coarse 28.00 1.1024

M24 x 2 dimensions

Nominal dimensions for M24 x 2. The basic internal minor diameter is the hole a 100% thread would start from, which is why no tap drill is ever that small.
Dimension Inch mm
Major diameter 0.9449 24.00
Basic internal minor diameter 0.8596 21.84
Pitch 0.0787 2.00
Thread designation M24 x 2

What the hole looks like

Cross-section of a M24 x 2 tapped hole, drawn to scale The drilled hole is 22 mm, 0.8661 inches or 22.00 millimetres across. The tap cuts outward from that wall to the major diameter of 0.9449 inches. A 100 percent thread would reach in to the basic minor diameter of 0.8596 inches, shown as a dashed line; the difference is why this drill gives 77.0% of thread. major 24 mm drill 22 mm · 22 mm dashed = 100% thread at 21.84 mm
M24 x 2 in section, to scale. The accent line is the thread the tap cuts from a 22 mm hole; the dashed line is where the crest would sit at 100% thread. The gap between them is the 23.0% of thread this drill leaves behind.

Work out a different hole for M24 x 2

Pre-filled with M24 x 2. Change the material, the tap type, or which drills you actually own, and it picks the closest real drill and tells you the percent of thread you end up with. The tables above are the published figures and do not depend on this.

The general-purpose target

Tap type
Drills you have

Best drill you have, cut tap, 70% target

7/8″0.875 in22.23 mm68.3% thread

Theoretical hole 22.18 mm

One size down, deeper thread22 mm 0.8661 in · 77.0%

One size up, easier tapping22.5 mm 0.8858 in · 57.7%

For comparison, the published chart drill for M24 x 2 is 22 mm at 77.0% thread.

Notes on M24 x 2

Middle pitch at this diameter
At 24 mm the data holds 3 pitches: M24 x 3, M24 x 2, M24 x 1.5. M24 x 2 sits between M24 x 3 and M24 x 1.5.
Not the same as M24 x 3
M24 x 3 and M24 x 2 share a 24 mm major diameter but not a pitch, and they take different drills: 21 mm for M24 x 3, 22 mm for M24 x 2. The taps and the fasteners are not interchangeable.
What the standard drill gives you
22 mm leaves 77.0% of thread (D - P). That is in the normal 65-80% band most shop charts aim for.
Stainless, tool steel and other tough material
22.5 mm opens the hole to 57.7% engagement. Less material for the tap to cut means less torque and less heat, at the cost of some thread depth.
Using a form (roll) tap
A form tap displaces metal instead of cutting it, so it needs a larger hole: 23 mm, against a theoretical 23.12 mm. Treat that as a starting point and check your tap maker's chart.
Closest inch size
1-8 is the nearest inch thread by diameter (25.4 mm against 24 mm). It is a planning reference only. The two are not interchangeable: the pitches differ, and a bolt from one will not run into a hole tapped for the other.

Related sizes

Same diameter, different pitch

Next size up and down

Closest inch size

1-8 7/8″ · 0.875 in · 22.23 mm · 77.0% 25.4 mm major against 24 mm

Not interchangeable. 1-8 is the nearest size by diameter, nothing more. The pitches differ, so a 1-8 fastener will not run into a M24 x 2 hole and forcing one will strip both.

Guides for tapping M24 x 2

Longer reads on the decisions behind the numbers above.

All guides →

M24 x 2 tap drill: common questions

What size drill bit do I need for a M24 x 2 tap?
A 22 mm drill, 0.8661 in. That leaves 77.0% of thread, which is the standard chart figure for M24 x 2.
What is the drill size for a M24 x 2 tap in inches?
The 22 mm tap drill measures 0.8661 in. If you only have inch drills, 55/64 in (0.8594 in) is the closest, giving 83.6% thread.
What drill should I use for M24 x 2 in stainless steel?
Use 22.5 mm instead of 22 mm. It leaves 57.7% of thread rather than 77.0%, so there is less material for the tap to cut and less chance of snapping it.
Is M24 x 2 the same as M24 x 1.5?
No. Both are 24 mm threads, but the pitch differs, so the drills differ: 22 mm for M24 x 2 and 22.5 mm for M24 x 1.5. The taps and the fasteners are not interchangeable.
What is the clearance hole for an M24 x 2 bolt?
For a medium fit, 26 mm per ISO 273. A clearance hole is not tapped; the bolt passes straight through it.
A 4 × 6 in card with the drills for this size.