Tap Drill Size Chart

M3.5 x 0.6 Tap Drill Size

Tap drill

2.9 mm 0.1142 in

Use a 2.9 mm drill (0.1142 in) for 77.0% thread.

The drill size for a M3.5 x 0.6 tap is 2.9 mm (0.1142 in). If you are wondering what size drill bit a M3.5 x 0.6 tap needs, that is the one: it leaves 77.0% of thread, which is the figure standard tap and drill charts are built around. Below are the other holes you might want for this size - a larger drill for tough material, the form-tap hole, and the clearance holes for the bolt that goes in.

Every drill for M3.5 x 0.6

Tap drills and clearance drills for M3.5 x 0.6 (Metric coarse, 0.6 mm pitch). Percent of thread is the figure stored for each drill, which reproduces from the major diameter and pitch of M3.5 x 0.6.
Use Drill Decimal in mm % thread
Standard tap drill Cut tap, general use (D - P) 2.9 mm 0.1142 2.90 77.0%
Inch substitute Closest inch drill if you have no metric set #33 0.113 2.87 80.8%
Hard material Stainless, tool steel, anything that fights the tap 3 mm 0.1181 3.00 64.2%
Form (roll) tap Theoretical 3.24 mm - starting point, check your tap maker's chart 3.2 mm 0.126 3.20 —

Clearance holes for a M3.5 x 0.6 bolt

A clearance hole is not tapped. It is the hole in the part the bolt passes through, so it is always larger than the thread.

Clearance holes for M3.5 x 0.6 per ISO 273. Clearance depends on the bolt diameter alone, so every M3.5 thread shares these figures.
Fit Hole mm Hole in
Fine 3.70 0.1457
Medium 3.90 0.1535
Coarse 4.20 0.1654

M3.5 x 0.6 dimensions

Nominal dimensions for M3.5 x 0.6. The basic internal minor diameter is the hole a 100% thread would start from, which is why no tap drill is ever that small.
Dimension Inch mm
Major diameter 0.1378 3.50
Basic internal minor diameter 0.1122 2.85
Pitch 0.0236 0.60
Thread designation M3.5 x 0.6

What the hole looks like

Cross-section of a M3.5 x 0.6 tapped hole, drawn to scale The drilled hole is 2.9 mm, 0.1142 inches or 2.90 millimetres across. The tap cuts outward from that wall to the major diameter of 0.1378 inches. A 100 percent thread would reach in to the basic minor diameter of 0.1122 inches, shown as a dashed line; the difference is why this drill gives 77.0% of thread. major 3.5 mm drill 2.9 mm · 2.9 mm dashed = 100% thread at 2.85 mm
M3.5 x 0.6 in section, to scale. The accent line is the thread the tap cuts from a 2.9 mm hole; the dashed line is where the crest would sit at 100% thread. The gap between them is the 23.0% of thread this drill leaves behind.

Work out a different hole for M3.5 x 0.6

Pre-filled with M3.5 x 0.6. Change the material, the tap type, or which drills you actually own, and it picks the closest real drill and tells you the percent of thread you end up with. The tables above are the published figures and do not depend on this.

The general-purpose target

Tap type
Drills you have

Best drill you have, cut tap, 70% target

2.95 mm0.1161 in70.6% thread

Theoretical hole 2.95 mm

One size down, deeper thread#32 0.116 in · 71.1%

One size up, easier tapping3 mm 0.1181 in · 64.2%

For comparison, the published chart drill for M3.5 x 0.6 is 2.9 mm at 77.0% thread.

Notes on M3.5 x 0.6

Only pitch in the data
M3.5 x 0.6 is the only pitch this chart lists at 3.5 mm, so there is no fine or coarse alternative to confuse it with.
What the standard drill gives you
2.9 mm leaves 77.0% of thread (D - P). That is in the normal 65-80% band most shop charts aim for.
Stainless, tool steel and other tough material
3 mm opens the hole to 64.2% engagement. Less material for the tap to cut means less torque and less heat, at the cost of some thread depth.
Using a form (roll) tap
A form tap displaces metal instead of cutting it, so it needs a larger hole: 3.2 mm, against a theoretical 3.24 mm. Treat that as a starting point and check your tap maker's chart.
Closest inch size
#6-32 is the nearest inch thread by diameter (3.51 mm against 3.5 mm). It is a planning reference only. The two are not interchangeable: the pitches differ, and a bolt from one will not run into a hole tapped for the other.

Related sizes

Next size up and down

Closest inch size

#6-32 #36 · 0.1065 in · 2.71 mm · 77.6% 3.51 mm major against 3.5 mm

Not interchangeable. #6-32 is the nearest size by diameter, nothing more. The pitches differ, so a #6-32 fastener will not run into a M3.5 x 0.6 hole and forcing one will strip both.

Guides for tapping M3.5 x 0.6

Longer reads on the decisions behind the numbers above.

All guides →

M3.5 x 0.6 tap drill: common questions

What size drill bit do I need for a M3.5 x 0.6 tap?
A 2.9 mm drill, 0.1142 in. That leaves 77.0% of thread, which is the standard chart figure for M3.5 x 0.6.
What is the drill size for a M3.5 x 0.6 tap in inches?
The 2.9 mm tap drill measures 0.1142 in. If you only have inch drills, #33 (0.113 in) is the closest, giving 80.8% thread.
What drill should I use for M3.5 x 0.6 in stainless steel?
Use 3 mm instead of 2.9 mm. It leaves 64.2% of thread rather than 77.0%, so there is less material for the tap to cut and less chance of snapping it.
What is the clearance hole for an M3.5 x 0.6 bolt?
For a medium fit, 3.9 mm per ISO 273. A clearance hole is not tapped; the bolt passes straight through it.
A 4 × 6 in card with the drills for this size.