Tap Drill Size Chart

3/4-20 Tap Drill Size

Tap drill

45/64″ 0.7031 in17.86 mm

Use a 45/64 in drill (0.7031 in, 17.86 mm) for 72.2% thread.

The drill size for a 3/4-20 tap is 45/64 in (0.7031 in / 17.86 mm). If you are wondering what size drill bit a 3/4-20 tap needs, that is the one: it leaves 72.2% of thread, which is the figure standard tap and drill charts are built around. Below are the other holes you might want for this size - a larger drill for tough material, the form-tap hole, and the clearance holes for the bolt that goes in.

Every drill for 3/4-20

Tap drills and clearance drills for 3/4-20 (UNEF (Unified extra fine), 20 TPI). Percent of thread is the figure stored for each drill, which reproduces from the major diameter and TPI of 3/4-20.
Use Drill Decimal in mm % thread
Standard tap drill Cut tap, general use (nearest to 75% (computed)) 45/64″ 0.7031 17.86 72.2%
Metric substitute Closest metric drill if you have no inch set 17.8 mm 0.7008 17.80 75.7%
Hard material Stainless, tool steel, anything that fights the tap 23/32″ 0.7188 18.26 48.0%
Form (roll) tap Theoretical 0.7279 in - starting point, check your tap maker's chart 47/64″ 0.7344 18.65 —

Clearance holes for a 3/4-20 bolt

A clearance hole is not tapped. It is the hole in the part the bolt passes through, so it is always larger than the thread.

Clearance holes for 3/4-20 per ASME B18.2.8. Clearance depends on the bolt diameter alone, so every 3/4 thread shares these figures.
Fit Drill Drill in Hole min in Hole max in Hole mm
Close 25/32″ 0.7812 0.781 0.789 19.84–20.04
Normal 13/16″ 0.8125 0.812 0.824 20.62–20.93
Loose 29/32″ 0.9062 0.906 0.926 23.01–23.52

3/4-20 dimensions

Nominal dimensions for 3/4-20. The basic internal minor diameter is the hole a 100% thread would start from, which is why no tap drill is ever that small.
Dimension Inch mm
Major diameter 0.750 19.05
Basic internal minor diameter 0.6959 17.68
Pitch (1 / TPI) 0.050 1.27
Threads per inch 20 TPI

What the hole looks like

Cross-section of a 3/4-20 tapped hole, drawn to scale The drilled hole is 45/64″, 0.7031 inches or 17.86 millimetres across. The tap cuts outward from that wall to the major diameter of 0.750 inches. A 100 percent thread would reach in to the basic minor diameter of 0.6959 inches, shown as a dashed line; the difference is why this drill gives 72.2% of thread. major 0.750 in drill 45/64″ · 0.7031 in dashed = 100% thread at 0.6959 in
3/4-20 in section, to scale. The accent line is the thread the tap cuts from a 45/64″ hole; the dashed line is where the crest would sit at 100% thread. The gap between them is the 27.8% of thread this drill leaves behind.

Work out a different hole for 3/4-20

Pre-filled with 3/4-20. Change the material, the tap type, or which drills you actually own, and it picks the closest real drill and tells you the percent of thread you end up with. The tables above are the published figures and do not depend on this.

The general-purpose target

Tap type
Drills you have

Best drill you have, cut tap, 70% target

17.9 mm0.7047 in69.7% thread

Theoretical hole 0.7045 in (17.9 mm)

One size down, deeper thread45/64″ 0.7031 in · 72.2%

One size up, easier tapping18 mm 0.7087 in · 63.6%

For comparison, the published chart drill for 3/4-20 is 45/64″ at 72.2% thread.

Notes on 3/4-20

Finest pitch at this diameter
3/4-20 is the finest of the standard pitches at 3/4 in. Fine threads suit thin walls and joints that see vibration, but the hole size matters more: the window between a weak thread and a broken tap is narrower than on 3/4-10.
Not the same as 3/4-10
3/4-10 and 3/4-20 share a 3/4 in major diameter but not a pitch, and they take different drills: 21/32 in for 3/4-10, 45/64 in for 3/4-20. The taps and the fasteners are not interchangeable.
What the standard drill gives you
45/64 in leaves 72.2% of thread (nearest to 75% (computed)). That is in the normal 65-80% band most shop charts aim for.
Stainless, tool steel and other tough material
23/32 in opens the hole to 48.0% engagement. Less material for the tap to cut means less torque and less heat, at the cost of some thread depth.
Using a form (roll) tap
A form tap displaces metal instead of cutting it, so it needs a larger hole: 47/64 in, against a theoretical 0.7279 in. Treat that as a starting point and check your tap maker's chart.
Closest metric size
M20 x 2.5 is the nearest metric thread by diameter (20 mm against 19.05 mm). It is a planning reference only. The two are not interchangeable: the pitches differ, and a bolt from one will not run into a hole tapped for the other.

Related sizes

Same diameter, different pitch

Next size up and down

Closest metric size

M20 x 2.5 17.5 mm · 0.689 in · 77.0% 20 mm major against 19.05 mm

Not interchangeable. M20 x 2.5 is the nearest size by diameter, nothing more. The pitches differ, so a M20 x 2.5 fastener will not run into a 3/4-20 hole and forcing one will strip both.

Guides for tapping 3/4-20

Longer reads on the decisions behind the numbers above.

All guides →

3/4-20 tap drill: common questions

What size drill bit do I need for a 3/4-20 tap?
A 45/64 in drill, 0.7031 in / 17.86 mm. That leaves 72.2% of thread, which is the standard chart figure for 3/4-20.
What is the drill size for a 3/4-20 tap in mm?
The 45/64 in tap drill measures 17.86 mm. If you only have metric drills, 17.8 mm is the closest, giving 75.7% thread.
What drill should I use for 3/4-20 in stainless steel?
Use 23/32 in instead of 45/64 in. It leaves 48.0% of thread rather than 72.2%, so there is less material for the tap to cut and less chance of snapping it.
Is 3/4-20 the same as 3/4-10?
No. Both are 3/4 in threads, but the pitch differs, so the drills differ: 45/64 in for 3/4-20 and 21/32 in for 3/4-10. The taps and the fasteners are not interchangeable.
What is the clearance hole for a 3/4-20 bolt?
For a normal fit, 13/16 in (0.8125 in), with the finished hole between 0.812 in and 0.824 in per ASME B18.2.8. A clearance hole is not tapped; the bolt passes straight through it.
A 4 × 6 in card with the drills for this size.